Difference between revisions of "Building Scalable DNS Cluster using LVS"

From LVSKB
Jump to: navigation, search
m (→‎[http://doc.powerdns.com/built-in-recursor.html PowerDNS recursor])
 
(13 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
== Introduction ==
 
== Introduction ==
  
 +
DNS (Domain Name Service) is one of the primary Internet services, which is to map human-friendly domain names to machine-friendly IP address. If there are a lot of people using DNS service (for example, subscribers use ISP's DNS server), one DNS server might be becoming a bottleneck, and the server might fail.
 +
 +
Scalable DNS cluster can help provide scalability and availability of DNS service.
 +
 +
The Example below is about setting up a cluster for recursive DNS but you can just as well use the same method for authorative DNS as well. Just remember that clients who use your cluster as a secondary nameservice would need to also-notify{} each of your realservers, not just the service-IP.
  
 
== Architecture ==
 
== Architecture ==
  
 +
DNS is a simple service, there is no affinity between requests from the same client. DNS usually listens for queries at UDP port 53 and TCP port 53.
 +
 +
LVS can simply load balance UDP port 53 and TCP port 53 among a set of DNS servers, and there is no need to setup any persistence options.
  
 
== Configuration Example ==
 
== Configuration Example ==
Line 39: Line 47:
 
on real_server kai we use the following netfilter setup to be able to direct the traffic to different BIND processes on the same machine/mac:
 
on real_server kai we use the following netfilter setup to be able to direct the traffic to different BIND processes on the same machine/mac:
 
  #DNAT 194.97.173.124->10.1.53.2 eth1.105
 
  #DNAT 194.97.173.124->10.1.53.2 eth1.105
−
  $ipt -t nat -A PREROUTING -i eth1.105 -s $net -d 194.97.173.124 -p tcp --dport 53 -j DNAT --to-destination 10.1.53.2:53
+
  iptables -t nat -A PREROUTING -i eth1.105 -s $net -d 194.97.173.124 -p tcp --dport 53 -j DNAT --to-destination 10.1.53.2:53
−
  $ipt -t nat -A PREROUTING -i eth1.105 -s $net -d 194.97.173.124 -p udp --dport 53 -j DNAT --to-destination 10.1.53.2:53
+
  iptables -t nat -A PREROUTING -i eth1.105 -s $net -d 194.97.173.124 -p udp --dport 53 -j DNAT --to-destination 10.1.53.2:53
 
  #DNAT 194.97.173.124->10.3.53.2 eth1.109
 
  #DNAT 194.97.173.124->10.3.53.2 eth1.109
−
  $ipt -t nat -A PREROUTING -i eth1.109 -s $net -d 194.97.173.124 -p tcp --dport 53 -j DNAT --to-destination 10.3.53.2:53
+
  iptables -t nat -A PREROUTING -i eth1.109 -s $net -d 194.97.173.124 -p tcp --dport 53 -j DNAT --to-destination 10.3.53.2:53
−
  $ipt -t nat -A PREROUTING -i eth1.109 -s $net -d 194.97.173.124 -p udp --dport 53 -j DNAT --to-destination 10.3.53.2:53
+
  iptables -t nat -A PREROUTING -i eth1.109 -s $net -d 194.97.173.124 -p udp --dport 53 -j DNAT --to-destination 10.3.53.2:53
  
 +
=== [http://www.isc.org/index.pl?/sw/bind/ BIND9] ===
  
−
We are using two BIND processes on the same machine for BIND9 currently just runs faster when it is not threading. Here is something Jinmei Tatuya told me on the bind9-workers Mailinglist which turned out to be very true:
+
When i wrote this example we were using two BIND processes on the same machine for BIND9 currently just runs faster when it is not threading. Here is something JINMEI Tatuya told me on the bind9-workers Mailinglist which turned out to be very true:
 
  If you go with disabling threads, you may also want to enable
 
  If you go with disabling threads, you may also want to enable
 
  "internal memory allocation".  (I hear that) it should use memory more
 
  "internal memory allocation".  (I hear that) it should use memory more
Line 60: Line 69:
 
  #define ISC_MEM_USE_INTERNAL_MALLOC 0
 
  #define ISC_MEM_USE_INTERNAL_MALLOC 0
 
  #endif
 
  #endif
−
Try it and you will keep it. ;)
+
Try it and you will keep it. ;)  
  
 +
BIND 9.4 line makes use of this new internal malloc library by default now, but disabling threading will probably free you from the hickups some BIND9 users are experiencing.
 +
 +
=== [http://doc.powerdns.com/built-in-recursor.html PowerDNS recursor] ===
 +
 +
This one is a recursive-only Nameserver with very limited authorative DNS capabilities. The author of this Example uses [http://doc.powerdns.com/built-in-recursor.html PowerDNS recursor] exclusively for his caching-only DNS cluster by now and is glad that while giving roughly the same queries per second performance it generates less SERVFAIL answers and is generally several times more robust than BIND9.
 +
 +
=== added redundancy via iBGP ===
  
 
If you have more than one Loadbalancer at different locations and you can convince your local Networker to let you speak BGP4+ to his routers you can use quagga with something like the following configuration to failover the service IP to the second LB if the first one goes down:
 
If you have more than one Loadbalancer at different locations and you can convince your local Networker to let you speak BGP4+ to his routers you can use quagga with something like the following configuration to failover the service IP to the second LB if the first one goes down:
Line 108: Line 124:
 
Here we fancy talking to two core-routers from each LB for extra redundancy.
 
Here we fancy talking to two core-routers from each LB for extra redundancy.
 
You can also have an internal anycast ServiceIP if you use the same metric at both LBs and make sure they are attached to the same level of router network-topology-wise. This way traffic gets shared between the two loadbalancers according to your network-topology most interesting of course for large dialin ISPs.
 
You can also have an internal anycast ServiceIP if you use the same metric at both LBs and make sure they are attached to the same level of router network-topology-wise. This way traffic gets shared between the two loadbalancers according to your network-topology most interesting of course for large dialin ISPs.
 +
 +
=== Problem ===
 +
 +
dig does not return a non-zero error code when receiving a SERVFAIL but there are situations when some BIND9 versions return SERVFAIL for any query for example when they are out of memory. For a recursive DNS cluster situation we would want to take such BIND processes out of service.
 +
 +
==== Workaround ====
 +
 +
use the following perl script as a wrapper for dig which is quite ugly for perl is an interpretated language and forking it is not much fun so this consumes much user cpu when executed every 6 seconds.
 +
#!/usr/bin/perl
 +
use strict;
 +
use warnings;
 +
# cmdline arguments: <FromIP> <Class> <QTYPE> <QNAME> <ToIP> <Times> <Tries> <ErrrorMatch> <Transport>
 +
# /usr/bin/dig -b 10.5.53.1 IN A 2.0.0.127.my.test @10.5.53.2 +time=1 +tries=5 +fail
 +
if(
 +
        ((defined $ARGV[0])&&($ARGV[0]=~/^\d+\.\d+\.\d+\.\d+$/))
 +
        &&((defined $ARGV[1])&&($ARGV[1]=~/^(IN|CHAOS)$/))
 +
        &&((defined $ARGV[2])&&($ARGV[2]=~/^(A|ANY|MX|PTR|SRV|TXT|AAAA|NS|CNAME|SOA)$/))
 +
        &&((defined $ARGV[3])&&($ARGV[3]=~/^[A-Za-z0-9\-\.]+$/))
 +
        &&((defined $ARGV[4])&&($ARGV[4]=~/^\d+\.\d+\.\d+\.\d+$/))
 +
        &&((defined $ARGV[5])&&($ARGV[5]=~/^\d+$/))
 +
        &&((defined $ARGV[6])&&($ARGV[6]=~/^\d+$/))
 +
        &&((defined $ARGV[7])&&($ARGV[7]=~/^\S+$/))
 +
        ) {
 +
        my $transport="notcp";
 +
        if((defined $ARGV[8])&&($ARGV[8]=~/^tcp$/i)) {
 +
                $transport="tcp";
 +
        } elsif ((defined $ARGV[8])&&($ARGV[8]=~/^udp$/i)) {
 +
                $transport="notcp";
 +
        }
 +
        my (@res)=`/usr/bin/dig -b $ARGV[0] $ARGV[1] $ARGV[2] $ARGV[3] \@$ARGV[4] +time=$ARGV[5] +tries=$ARGV[6] +fail +$transport 2>&1`;
 +
        my $return=$?;
 +
        if(my $error=(map {/status:\s*($ARGV[7])/ ? $1 : ()} @res)[0]) {
 +
                die("$error");
 +
        } elsif ($return!=0) {
 +
                die("dig returned: \"$return\"");
 +
        } elsif ($return==0) {
 +
                exit 0;
 +
        } else {
 +
                die("error: \"$return\" HAS BAD VALUE!");
 +
        }
 +
} else {
 +
        die("dig-wrapper.pl <FromIP> <Class> <QTYPE> <QNAME> <ToIP> <Times> <Tries> <ErrrorMatch> <Transport>");
 +
}
 +
Ah yes, forgot to say: The Dual PIII 800 is not idleing around anymore - its busy running this script 44 times every 6 seconds, which accounts for roughly 12% user cpu and 5% system used at a query rate of ~3600q/s.
 +
 +
==== Solution ====
 +
 +
use a patched version of dig?
  
 
== Conclusion ==
 
== Conclusion ==
  
−
It just works.
+
It still just works.
  
  

Latest revision as of 17:57, 30 October 2008

Introduction

DNS (Domain Name Service) is one of the primary Internet services, which is to map human-friendly domain names to machine-friendly IP address. If there are a lot of people using DNS service (for example, subscribers use ISP's DNS server), one DNS server might be becoming a bottleneck, and the server might fail.

Scalable DNS cluster can help provide scalability and availability of DNS service.

The Example below is about setting up a cluster for recursive DNS but you can just as well use the same method for authorative DNS as well. Just remember that clients who use your cluster as a secondary nameservice would need to also-notify{} each of your realservers, not just the service-IP.

Architecture

DNS is a simple service, there is no affinity between requests from the same client. DNS usually listens for queries at UDP port 53 and TCP port 53.

LVS can simply load balance UDP port 53 and TCP port 53 among a set of DNS servers, and there is no need to setup any persistence options.

Configuration Example

keepalived.conf: 

! Balancer-Set for udp/53
virtual_server 194.97.173.124 53 {
   delay_loop 10
   lb_algo wrr
   lb_kind DR
   protocol UDP
   ! persistence_timeout 1
   ! persistence_granularity 255.255.255.255
   ! eth1.105 -> kai eth1.105
   real_server 10.1.53.2 53 {
       weight 1
       MISC_CHECK {
           misc_path "/usr/bin/dig -b 10.1.53.1 a resolve.test.roka.net @10.1.53.2 +time=1 +tries=5 +fail > /dev/null"
           misc_timeout 6
       }
   }
   ! eth1.109 -> kai eth1.109
   real_server 10.3.53.2 53 {
       weight 1
       MISC_CHECK {
           misc_path "/usr/bin/dig -b 10.3.53.1 a resolve.test.roka.net @10.3.53.2 +time=1 +tries=5 +fail > /dev/null"
           misc_timeout 6
       }
   }
}

As you can dig (;-) we are using an A record with a low TTL to test the service for this setup is a recursive DNS cluster. So far dig works fine with 44 real_servers configured on an idle Dual PIII 800.


on real_server kai we use the following netfilter setup to be able to direct the traffic to different BIND processes on the same machine/mac: 

#DNAT 194.97.173.124->10.1.53.2 eth1.105
iptables -t nat -A PREROUTING -i eth1.105 -s $net -d 194.97.173.124 -p tcp --dport 53 -j DNAT --to-destination 10.1.53.2:53
iptables -t nat -A PREROUTING -i eth1.105 -s $net -d 194.97.173.124 -p udp --dport 53 -j DNAT --to-destination 10.1.53.2:53
#DNAT 194.97.173.124->10.3.53.2 eth1.109
iptables -t nat -A PREROUTING -i eth1.109 -s $net -d 194.97.173.124 -p tcp --dport 53 -j DNAT --to-destination 10.3.53.2:53
iptables -t nat -A PREROUTING -i eth1.109 -s $net -d 194.97.173.124 -p udp --dport 53 -j DNAT --to-destination 10.3.53.2:53

BIND9

When i wrote this example we were using two BIND processes on the same machine for BIND9 currently just runs faster when it is not threading. Here is something JINMEI Tatuya told me on the bind9-workers Mailinglist which turned out to be very true: 

If you go with disabling threads, you may also want to enable
"internal memory allocation".  (I hear that) it should use memory more
efficiently (and can make the server faster) but is disabled by
default due to response-performance reasons in the threaded case.  You
can enable this feature by adding the following line

#define ISC_MEM_USE_INTERNAL_MALLOC 1

just before the following part of bind9/lib/isc/mem.c:

#ifndef ISC_MEM_USE_INTERNAL_MALLOC
#define ISC_MEM_USE_INTERNAL_MALLOC 0
#endif

Try it and you will keep it. ;)

BIND 9.4 line makes use of this new internal malloc library by default now, but disabling threading will probably free you from the hickups some BIND9 users are experiencing.

PowerDNS recursor

This one is a recursive-only Nameserver with very limited authorative DNS capabilities. The author of this Example uses PowerDNS recursor exclusively for his caching-only DNS cluster by now and is glad that while giving roughly the same queries per second performance it generates less SERVFAIL answers and is generally several times more robust than BIND9.

added redundancy via iBGP

If you have more than one Loadbalancer at different locations and you can convince your local Networker to let you speak BGP4+ to his routers you can use quagga with something like the following configuration to failover the service IP to the second LB if the first one goes down: 

!
router bgp 5430
 no synchronization
 bgp router-id a.b.c.d
 redistribute connected route-map benice
 neighbor c.d.e.f remote-as 5430
 neighbor c.d.e.f description ffm4-j2
 neighbor c.d.e.f send-community both
 neighbor c.d.e.f soft-reconfiguration inbound
 neighbor c.d.e.f route-map nixda in
 neighbor c.d.e.f route-map benice out
 neighbor d.c.f.e remote-as 5430
 neighbor d.c.f.e description ffm4-j
 neighbor d.c.f.e send-community both
 neighbor d.c.f.e soft-reconfiguration inbound
 neighbor d.c.f.e route-map nixda in
 neighbor d.c.f.e route-map benice out
 no auto-summary
!
access-list line permit 127.0.0.1/32 exact-match
access-list line deny any
!
ip prefix-list cns-dus2 description dus2 high-metric eq low-perference
ip prefix-list cns-dus2 seq 5 permit 194.97.173.125/32
ip prefix-list cns-dus2 seq 10 deny any
ip prefix-list cns-ffm4 description ffm4 low-metric eq high-preference
ip prefix-list cns-ffm4 seq 5 permit 194.97.173.124/32
ip prefix-list cns-ffm4 seq 10 deny any
!
route-map benice permit 10
 match ip address prefix-list cns-ffm4
 set local-preference 100
 set metric 0
!
route-map benice permit 20
 match ip address prefix-list cns-dus2
 set local-preference 100
 set metric 1
!
route-map nixda deny 10
!

This is the LB at FFM4. Note that the metric at the DUS2 LB is just the other way around. Here we fancy talking to two core-routers from each LB for extra redundancy. You can also have an internal anycast ServiceIP if you use the same metric at both LBs and make sure they are attached to the same level of router network-topology-wise. This way traffic gets shared between the two loadbalancers according to your network-topology most interesting of course for large dialin ISPs.

Problem

dig does not return a non-zero error code when receiving a SERVFAIL but there are situations when some BIND9 versions return SERVFAIL for any query for example when they are out of memory. For a recursive DNS cluster situation we would want to take such BIND processes out of service.

Workaround

use the following perl script as a wrapper for dig which is quite ugly for perl is an interpretated language and forking it is not much fun so this consumes much user cpu when executed every 6 seconds. 

#!/usr/bin/perl
use strict;
use warnings;
# cmdline arguments: <FromIP> <Class> <QTYPE> <QNAME> <ToIP> <Times> <Tries> <ErrrorMatch> <Transport>
# /usr/bin/dig -b 10.5.53.1 IN A 2.0.0.127.my.test @10.5.53.2 +time=1 +tries=5 +fail
if(
       ((defined $ARGV[0])&&($ARGV[0]=~/^\d+\.\d+\.\d+\.\d+$/))
       &&((defined $ARGV[1])&&($ARGV[1]=~/^(IN|CHAOS)$/))
       &&((defined $ARGV[2])&&($ARGV[2]=~/^(A|ANY|MX|PTR|SRV|TXT|AAAA|NS|CNAME|SOA)$/))
       &&((defined $ARGV[3])&&($ARGV[3]=~/^[A-Za-z0-9\-\.]+$/))
       &&((defined $ARGV[4])&&($ARGV[4]=~/^\d+\.\d+\.\d+\.\d+$/))
       &&((defined $ARGV[5])&&($ARGV[5]=~/^\d+$/))
       &&((defined $ARGV[6])&&($ARGV[6]=~/^\d+$/))
       &&((defined $ARGV[7])&&($ARGV[7]=~/^\S+$/))
       ) {
       my $transport="notcp";
       if((defined $ARGV[8])&&($ARGV[8]=~/^tcp$/i)) {
               $transport="tcp";
       } elsif ((defined $ARGV[8])&&($ARGV[8]=~/^udp$/i)) {
               $transport="notcp";
       }
       my (@res)=`/usr/bin/dig -b $ARGV[0] $ARGV[1] $ARGV[2] $ARGV[3] \@$ARGV[4] +time=$ARGV[5] +tries=$ARGV[6] +fail +$transport 2>&1`;
       my $return=$?;
       if(my $error=(map {/status:\s*($ARGV[7])/ ? $1 : ()} @res)[0]) {
               die("$error");
       } elsif ($return!=0) {
               die("dig returned: \"$return\"");
       } elsif ($return==0) {
               exit 0;
       } else {
               die("error: \"$return\" HAS BAD VALUE!");
       }
} else {
       die("dig-wrapper.pl <FromIP> <Class> <QTYPE> <QNAME> <ToIP> <Times> <Tries> <ErrrorMatch> <Transport>");
}

Ah yes, forgot to say: The Dual PIII 800 is not idleing around anymore - its busy running this script 44 times every 6 seconds, which accounts for roughly 12% user cpu and 5% system used at a query rate of ~3600q/s.

Solution

use a patched version of dig?

Conclusion

It still just works.


LVS.png "Building Scalable DNS Cluster using LVS" is an LVS Example related stub. You can help LVSKB by expanding it
Retrieved from "http://kb.linux-vs.org/wiki?title=Building_Scalable_DNS_Cluster_using_LVS&oldid=5783"